2.- Creation of sinusoidal graph. Shift to the left.
p299Hi_GraficoDinamico_2.aia (10.9 KB)
Look at the properties of the extension.
MaxValue: 1000
MinValue: -1000
3.- Arduino. Bluetooth Potentiometer.
p299Hi_GraficoDinamico_3.aia (11.4 KB)
Arduino sends the value of a potentiometer over Bluetooth.
// Juan A. Villalpando
// http://kio4.com/appinventor/299H_extension_GraficoDinamico.htm
int value_pot0;
void setup() {
Serial.begin(9600);
}
void loop() {
value_pot0 = analogRead(A0);
// value_pot0 = (int) random(0,1023);
Serial.println(value_pot0);
delay(100); // It should be slower than the Clock Interval.
}
4.- Creation of two and three graphs with random values. Shift to the left.
p299Hi_GraficoDinamico_4.aia (11.4 KB)
4B.- Creation of three graphs with random values. Set max and min values. Shift to the left.
p299Hi_GraficoDinamico_6.aia (16.5 KB)
- If we set the color to 16774127, that graph will not be displayed.
- We can set the maximum and minimum values of each graph.
Great Extension @Juan_Antonio
BTW , is this HC-05 bluetooth module?
Actually if its a HC-05 module it, there is KEY pin 
, it looks like a different variant of it...
HC-05 and HC-06 here
Great job Juan Antonio !!! 
To do the same I was using a canvas split in two sections (a left one , mirroring the right one) but the effect was not continuous like yours (i.e. such as a scrolling track on an oscilloscope). Thanks a lot: this will be a big improvement in my "digital HUD" for my old convertible.
Cheers, Ugo.
(added to FAQ)
Amazing job @Juan_Antonio!
I have implemented similar moving real-time graphs using the timers and recursive draw functions, but this extension would make the process so easier!
5.- Screen1 to connect. Screen2 to view data.
p299H_GraficoDinamico_5.aia (12.6 KB)
The application must be installed
- Screen1 to select and connect Bluetooth.
- Screen2 to view data graphic with an extension.
- We can go from one Screen to another without losing the connection.
Screen1.
Screen2.
// Juan A. Villalpando
// http://kio4.com/appinventor/299H_extension_GraficoDinamico.htm
#include <SoftwareSerial.h>
SoftwareSerial BT(2,3);
String texto = "";
void setup(){
BT.begin(9600);
Serial.begin(9600);
}
void loop(){
// Send random every 800 ms.
delay(800);
texto = (String) random(0,1000);
// Serial.println(texto);
texto = texto + '\n';
BT.write(texto.c_str());
// If receive BT, write.
if(BT.available()) {
Serial.write(BT.read());
}
// If Serial Monitor, send data by BT
if(Serial.available()){
texto = Serial.readStringUntil('\n');
texto = texto + '\n';
BT.write(texto.c_str());}
}
- Sketch sends random every 800 ms. by BT.
- You can write a number on Serial Monitor and send it by BT.
- You can write a text in the app and send it to Arduino by BT (check Serial Monitor).
(added to FAQ)
Hello dear ,
I want to stop the shifting at a certain point .. how to freeze it ? Like my Arduino sensor is sending bell shape once it hits back the zero Y I want to stop it ? I see we have two options , either one screen … no shift or keep going shift left forever … how can I stop the graph as is at a certain point ? … thank you so much for your help
You can do the control on the Arduino,
(schematic code:)
if valueinArduino = 0 then sendtoapp 999999
Then in App
if ReceiveText = 999999 then Clock.Enabled=false
thank you so much .. working like a charm ! ... now i have full control of it except i am missing the following:
1- my horizontal x line can be 2 min or 2 hours ... if i need both cases to be in ONE screen .. how can i change X scale according? (before i start plotting i do not know in advance if it will be 2 min or 50 min or 2 h ..) ... can i zoom in out ? like using two fingers to change x scale ?
2- lets say case one above is not possible and my x for one screen wide of my cell is 10 staps while my graph is 30 steps ( like 3 screens wide) once graph done .. can i scroll right - left to see the whole graph in the 3 screen width?
btw i tried changing the kio4 dynamicgraph.resolution > to Slider1.thumbposition which works fine with NEW upcoming data to be plotted, not the previously plotted data.
6.- Save all values in a List. Show graph with saved values.
p299Hi_GraficoDinamico_7.aia (18.4 KB)
Save all the values in a list.
Pause.
Using a Slider to display graphics on the Canvas with the saved values.
thank you
google chart means my cell must be connected to internet right ? .. i mean if i need it to plot the graph offline (i am using bleutooth to arduino) .. can i save the google js file at the arduino then that file will generate the grapf without need of uploading it to google chart live?.. possible?
thank you
OMG ! i never thought i can use google chart with off line ! .. now i can make either Bluetooth or access point and while my cell is NOT on the internet data and even draw the graph ! this is great tutorial in your link .. not sure why i never came across it ! .. maybe cuz i was searching in english while its original is Spanish (i guess ! , i asked google to translate it so i know what is that ..etc ) sorry i know 3 languages but Spanish is not one of them . have a wonderful weekend.